Click on the topic below:
-
We are offering JetSurf board rental only for customers who already have one and know how to use it properly. If you want to try JetSurf, visit JetSurf Academy USA website and schedule your ride! Rental pricelist: 1 day: $150 2 days: $250 3 days: $300 7 days: $800 ...
-
Do you want to try the JetSurf board? Visit our JetSurf Academy.
We have a couple of JetSurf Academies that you can choose to go and learn how to ride! We guarantee an incredible experience! Check out this funny VIDEO from JetSurf Academy in Miami Please go to http://www.jetsurfacademyusa.com/ and choose a place and time that works best for you! -
For what is the indicator next to the hood
The indicator has several functions: SIGNALLING: – Signalling the ride duration – Signalling the conditions and errors of the ICU control unit CONTROLLING: – By BRIEFLY placing your key to the indicator you will switch the ICU off and on – By placing and LEAVING the key on the indicator, you will... -
How can I check the water in the engine
If the engine does not turn or turns slowly, it may be caused by engine flooded by water. *Water in the engine symptoms: white emulsion the spark plug. * How to check it? Pull the spark plug from the engine. Take the holder from the spark plug boot and remove the boot from the spark plug. Screw... -
How can I find out If there is too much fuel in the engine
Too much fuel in the engine symptoms: the spark plug is soiled with petrol. 1) Check the spark plug. 2) Check the carburettor set-up. -
How do I find out that the engine is free to turn - freewheel test
Do a freewheel test: Turn the engine by hand at driveshaft coupling place. In one direction the main gear wheel must turns. In the opposite direction, the main gear cannot turn. If the freewheel is damaged, contact our service, please. -
How much do we charge for one labour hour
1 labour hour cost $120. -
The carburettor is a vital part of the engine and it requires highly sophisticated adjustments. Most adjustments should be left for the JetSurf™ sales representative who has the required knowledge and experience. The carburettor has three basic adjusting screws: 1 - A screw for adjusting the fr...
-
Thank you for your interest in jet surfboards! You can make your order HERE.
-
How to change a JetSurf spark plug
Please take a look at our instructional VIDEO. PROCEDURE: – Before every assembly, remove the tank: disconnect the hoses and undo the velcro with which the tank is attached. – Check the engine, of it, is not too hot. We recommend performing the assembly minimum 0.5 hours after the engine was swi... -
How to change the timing sensor in JetSurf
Please take a look at our instructional VIDEO. **PROCEDURE: Before every assembly, take out the tank: disconnect 2 tubes from the tank and undo the velcro which attaches the tank. Check whether the engine is not hot. We recommend performing the assembly minimum of 0.5 hours after the engine is ... -
Disconnect the 4-pin connector (marked with a red cable tie) which is connected in the connector holder. Connect the charger to a 12 V socket in the car or to a 110/220 V power cable. Never charge the battery while the car is moving as there is a danger of damage to both the charger and the ignit...
-
How to check the correct function of the throttle cable
Try to pull the throttle trigger, it has to run easily. Try If the relay in the control handle does not detect the engine shut-off key. Check the contacts and connectors on the control handle cable, If you find a problem. -
Regularly check (check for example for plastic bags) and clean the exhaust ending and its parts.
-
How to check the spark plug and timing sensor function
PROCEDURE: – Check that the engine is not hot. We recommend performing the assembly minimum 0.5 hours after the engine is switched off. – Check that the ICU control unit is not on (the indicator is not on or flashing)! CONNECTING THE MOUNTING TOOL FOR SPARK PLUG TESTING 1) Remove the boot holder... -
How to connect and disconnect JetSurf fuel tank
Please take a look at our instructional VIDEO. FUEL TANK REMOVAL 1) Disconnect the second CPC coupling connecting the tube coming out of the tank to the tube going to the carburettor. The CPC coupling has a security clip which must be pressed when disconnected. 2) Undo the velcro on the tank. 3)... -
How to connect the fuel tank correctly
FUEL TANK REMOVAL Disconnect the second CPC coupling connecting the tube coming out of the tank to the tube going to the carburettor. The CPC coupling has a security clip which must be pressed when disconnected. Undo the velcro on the tank. Move the tank out upwards. Disconnect the hose on the o... -
How to connect the mounting tools for spark plug testing
CONNECTING THE MOUNTING TOOL FOR SPARK PLUG TESTING 1) Remove the boot holder from the spark plug boot and remove the boot. 2) Screw the spark plug out using a spark plug spanner. Check the spark plug and possibly dry it. 3) Insert the spark plug back into the spark plug boot. 4) Place the cap on... -
How to fly on the plane with your JetSurf motorized surfboard
Please take a look at our instructional VIDEO. Airline companies do not like fuel in luggage and may refuse to transport your power board. Therefore it is ABSOLUTELY NECESSARY to wash the fuel tank completely before air transport of your power board. Wash the tank with water and detergent. Repea... -
Please take a look at our instructional VIDEO. FASTENING OF SIDE (SMALL) FINS: First, unscrew the long screw which is screwed in the fin. Slide the side fin into the opening in the bottom side of the board. Make sure that the fins are oriented correctly. Find the opening in the top side of the p...
-
How to maintenance electric bilge pump
The bilge pump suck water from the internal area of JetSurfTM. It is a vital part of the JetSurf operation. During every ride, check whether the pump works properly. Keep the suction filter clean. SUCTION FILTER CLEANING PROCEDURE: Required tools: key No 10 1) Remove the rubber O-ring from the c... -
How to make the right mixture of gas and oil for JetSurf
Please take a look at our instructional VIDEO. PETROL TO OIL MIXTURE is 50:1 (50 parts of petrol:1 part of oil) Example: To 1 litre of petrol add 0.02 l (20 ml) of oil. To 2 litres of petrol add 0.04 l (40 ml) of oil. -
PROCEDURE: - Before every assembly, take out the tank: disconnect 2 tubes from the tank an undo the velcro which attaches the tank. - Check whether the engine is not hot. We recommend performing the assembly minimum of 0.5 hours after the engine is switched off. - Check whether the ignition is n...
-
How to replace ignition control unit (ICU)
PROCEDURE: - Before every assembly, take out the tank: disconnect 2 tubes from the tank an undo the velcro which attaches the tank. - Check whether the engine is not hot. We recommend performing the assembly minimum of 0.5 hours after the engine is switched off. - Check whether the ignition is n... -
PROCEDURE: - Before every assembly, take out the tank: disconnect 2 tubes from the tank and undo the velcro which attached the tank. - Check whether the engine is not hot. We recommend performing the assembly minimum of 0.5 hours after the engine is switched off. - Check whether the ignition is n...
-
How to start the JetSurf board
The starting process has two stages. STAGE ONE – ICU activation Insert the engine shut-off key in the engine shut-off switch placed on the upper part of the control handle for minimum 4 seconds (BUT LONGEST FOR 30 SECONDS!!!), then take the key out. The ignition control unit (ICU) will switch o... -
How to transport the JetSurf board
ALWAYS TRANSPORT JETSURF WITHOUT THE FUEL TANK INSIDE THE BOARD. Before transporting the power board, make sure that there is no water in the exhaust system. It could get into the engine during the transport. Always unscrew both side and main fins (if they are included). NOTE: If you have a two-... -
Please take a look at our instructional VIDEO. STAND AND ITS UNFOLDING Every JetSurf™ is supplied with a light stand. The stand should be used on a solid levelled surface and it is only used to keep the JetSurf motorized power board in a comfortable height. Use of the JetSurf stand is strongly r...
-
How to wash JetSurf board properly from salt water
Please take a look at our instructional VIDEO. To store the power board overnight, find a freshwater source (e.g. a garden hose) and wash the inside of the board thoroughly (be careful and prevent any water getting into the carburettor). Then let the engine run for 5 more seconds (MAXIMUM for 10... -
Ignition Control Unit (ICU) basic states and signals
The electronic ignition system has six basic states: – POWER OFF – RIDE – POWER ON (ICU DIAGNOSTICS), – ENGINE CLEARING – IDLE (INITIAL STATE) – FAULT These states are signalised with a two-colour LED situated on the front of ICU between the conductor bundles. These conditions are signalled by th... -
Logistic & shipping information (dimensions, weight) for one JetSurf Board package
dimensions: inches: 72x28x10 centimeters :68,58 x71,12x25,4 weight: 70 lbs 31,751 Kg -
You haven't enough space for your JetSurf board? You would like to store your board in Miami? No problem! We are offering you storage in our Miami headquarter. One month - one board for $100. If you are interested, email us at support@jetsurfusa.com.
-
Rent a board without the lesson
Can I rent a board without a lesson? Yes, if you are JetSurf board owner. price: $150 / day $250 / 2 days $350 / 3 days $750 / 7 days $2000 deposit -
Due to the limited spaces, we will store your board for 10 days after the service. For every day after the aforementioned 10 days; we will charge a storage fee of $ 5 per day. Thank you for understanding!
-
Tilt the JetSurf and pour the water out of it Start the JetSurf with its tip up, MAXIMUM FOR 10 seconds! Wash the whole JetSurf with fresh water, including the engine compartment, then let the engine run for about 5 seconds Let the JetSurf dry Spray all the engine parts thoroughly with MOTOREX IN...
-
What is Balance mode in charger menu
Balance charge mode is intended for charging after the last ride of the day. Select this mode when charging JetSurf for the first time -
What is goofy and regular stance
In essence, Regular and goofy are terms used to describe how one would stand on a power board. Regular means that the left foot is placed forward, while Goofy means that the right foot is placed forward. Your front foot will be facing forward always. -
Ignition Control Unit - electronic control element of JetSurf engine. ICU is composed of 3 parts: ICU with internal batteries, ignition coil, engine starter.
-
What is regular maintenance of JetSurf board
Once every 12 months, we recommend performing a complete service inspection. SURFACE MAINTENANCE: Maintaining a top layer of quality wax on the surface of the motorized power board is crucial for the keeping of the original high gloss surface to come. Use only high-quality wax, such as carnauba ... -
What is Storage mode in charger menu
In winter or when JetSurf is not used, it is necessary to charge the battery in ICU at least once in every 3 months. Charging mode STORAGE – it is intended for charging for storage. -
What is the difference between a carburettor and DFI JetSurf board
A carburettor is a device in an internal combustion engine for mixing air with a fine spray of liquid fuel. DFI (Digital Fuel Injection) is a fuel injection system that uses a digital signal from an onboard ICU for efficient fuel and air mixing. -
What is the electric bilge pump
The bilge pumps suck water from the internal area of JetSurf. They are a vital part of the JetSurf operation. Please check the function of the bilge pumps before every ride and during the ride. Keep the suction filters clean. -
A crank sensor is an electronic device used in an engine to monitor the position or rotational speed of the crankshaft. This information is used by engine management systems (ICU) to control the fuel injection or the ignition system timing and other engine parameters.
-
• Attach the fins (2 side ones and 1 main one) • Set the straps • Charge the batteries in the ICU • Top up the fuel • Check the tubes of the cooling system and all the connections and tubes • Check whether all the connectors are connected • Check the spark plug boot, check the spark plug, check t...
-
What to do if the relay in the control handle does not detect the engine shut-off key
1) Check if the ICU battery is charged. 2) Plug the shut-off key to switch on the handle. 3) If the ICU still don't have a signal, check the contacts and connectors on the control handle cable If there is no damage. -
What to do when the charger shows ERROR – Lower cell voltage
Go out from Standard menu to menu Smart battery. Change setup to 12.6V and press Start. Charge the battery for 10 minutes, then Stop. Go back to the Standard mode and charge battery to full. -
What to do when the engine is flooded by water
Pull the spark plug from the engine. Take the holder from the spark plug boot and remove the boot from the spark plug. Screw the spark plug out using a spark plug spanner which is supplied within the accessories. If the spark plug is wet - dry it. Tilt the JetSurf™ towards the spark plug opening ... -
What to do when the engine turns slowly or does nothing
INSTRUCTIONS: Check that ICU is charged. Charge the ICU battery. Do water in the engine test (see ''How can I check the water in the engine'' FAQ). Remove water from the engine. Do the freewheel test. (see ''How do I find out that engine is free to turn. Freewheel test'' FAQ). Test the starter R... -
What to do when the ICU does not flash
Charge the battery. Check the ICU cables and connectors. -
What to do when the JetSurf board does not start but the engine turns
1) Search for water in the engine (symptoms: white emulsion on the spark). 2) Check if there is no too much fuel in the engine (symptoms: the spark plug is soiled with petrol) 3) Check if there is fuel in the engine (symptoms: dry spark plug, empty fuel tubing) 4) Check if the spark plug sparks (... -
What to do when the spark plug does not spark
The spark plug can be wet by fuel or by water. Remove the spark plug (follow the instruction in the User manual) and dry it or put new spark plug. -
What to do with my JetSurf board in the winter break. Storage
When the engine running after the engine shut-off key is pulled out, it means that there is a problem with the timing sensor. Check whether the timing sensor is attached properly to the crankshaft. Look for damages on the cable. If cables and connectors look fine, it's necessary to replace the t... -
What to do with my JetSurf board in winter break. Storage
If the break is longer than one week, it is necessary to perform other tasks. Do not underestimate these steps. Keep in mind that if you look after the JetSurf properly, you will increase the life of all its parts. For at least 3 days always start the engine and accelerate several times. Take th... -
Where to buy JetSurf merchandise
If you are looking for our clothes and accessories, visit our website. -
If you would like to buy JetSurf spare parts or components, visit our website, please.